Plumbing for Beginners: What You Need for Installing a Bathtub
Plumbing for Beginners: What You Need for Installing a Bathtub
Blog Article
We've noticed this article relating to Tools You Need to Install a New Bathtub directly below on the internet and thought it made perfect sense to relate it with you here.
Mounting a bath tub isn't exactly brain surgery, however it does need solid plumbing, woodworking, as well as in some cases, tiling skills. Changing an old bath tub with a brand-new one is also a reasonably tough project. If the old tub is easily available, the job can relocate immediately; if you need to open a wall to get rid of the old bathtub and place the new bath tub, the task is a lot harder. In either case, the job is within a residence handyman's skills, although you will require an assistant to move out the old tub and embeded in the brand-new one. Make certain you have actually certified on your own for the job and fit trying it. As opposed to employing a service provider to take control of a halfway-completed project, it is much better to take into consideration using one prior to you start. Opportunities are you might require a specialist plumber to make tube links.
This write-up will certainly assist you set up a brand-new bath tub in your washroom if you have actually already purchased a new bathtub and also don't require to alter the arrangement of your previous water supply pipelines.
Your tools and product checklist should make up the following:
Getting ready for the Setup
First of all, the sustaining framework supplied with the bath should be fitted (if required) according to the manufacturer's guidelines. Next off, fit the faucets or mixer to the bath tub. When suitable the faucet block, it is necessary to make sure that if the tap features a plastic washer, it is fitted between the bathroom and also the faucets. On a plastic bathroom, it is likewise reasonable to fit a sustaining plate under the taps system to avoid stress on the tub.
Fit the versatile tap ports to the bottom of the two taps using 2 nuts and olives (often supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and then pass the electrical outlet with the hole in the bath. Use the nut provided by the manufacturer to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the flexible overflow pipeline to the overflow outlet. Afterwards, screw the pipeline to the overflow face which should be fitted inside the bathroom. Ensure you make use of all of the provided washing machines.
Connect the catch to the bottom of the waste outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Connect the bottom of the overflow tube in a similar manner.The bath ought to now be ready to be fitted in its last placement.
Removing Old Touches
If you require to replace old faucets with new ones as a part of your installment, after that the first thing you must do is detach the water system. After doing so, switch on the taps to drain any kind of water continuing to be in the system. The procedure of getting rid of the existing faucets can be rather problematic due to the limited gain access to that is typically the case.
Make use of a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that attaches the supply pipes to the faucets. Have a fabric all set for the staying water that will certainly come from the pipelines. Once the supply pipelines have been gotten rid of, use the exact same device to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to stop the solitary taps from transforming throughout this process. When the faucets have actually been removed, the holes in the bath/basin will need to be cleansed of any type of old securing substance.
Prior to proceeding to fit the new faucets, contrast the pipeline links on the old faucets to the new taps. If the old taps are longer than the new taps, then a shank adapter is required for the new faucets to fit.
Setting up the Bathtub
Utilizing both wood boards under its feet, position the tub in the required position. The wooden boards are handy in equally spreading out the weight of the bath tub over the location of the boards rather than focusing all the weight onto four small factors.
The following goal is to guarantee that the bathtub is leveled all round. This can be attained by examining the spirit level and adjusting the feet on the bath tub up until the spirit level reviews degree.
To set up faucets, fit all-time low of the furthest adaptable faucet connector to the proper supply pipe by making a compression sign up with; then do the same for the various other faucet.
Turn on the supply of water and also inspect all joints and brand-new pipework for leaks and also tighten them if required. Load the bathtub as well as additionally inspect the overflow electrical outlet and the typical electrical outlet for leakages.
Finally, fix the bath paneling as explained in the supplier's instruction manual. Tiling as well as securing around the bath tub should wait until the tub has been utilized a minimum of when as this will resolve it into its final placement.
Fitting New Taps
If the tails of the brand-new taps are plastic, then you will require a plastic port to stop damages to the string. One end of the adapter fits on the plastic tail of the faucet and also the other end provides a connection to the current supply pipelines.
If you require to fit a monobloc, then you will certainly call for reducing couplers, which connects the 10mm pipeline of the monobloc to the common 15mm supply pipeline.
Next, place the tap in the mounting opening in the bath/basin making certain that the washing machines are in place in between the faucet as well as the sink. Secure the faucet in place with the manufacturer provided backnut. As soon as the tap is securely in position, the supply pipes can be attached to the tails of the taps. The faucets can either be connected by using corrugated copper piping or with typical faucet connectors. The previous kind needs to be connected to the tap ends first, tightening up only by hand. The supply pipelines can later be linked to the other end. Tighten both ends with a spanner after both ends have been attached.
Tiling Around the Tub
In the location where the bath fulfills the floor tile, it is essential to secure the joins with a silicone rubber caulking. This is very important as the installation can move sufficient to break an inflexible seal, causing the water to pass through the wall in between the bath as well as the tiling, leading to issues with wetness and possible leakages to the ceiling listed below.
You can choose from a variety of coloured sealers to blend in your components as well as installations. They are offered in tubes and also cartridges, as well as are capable of securing gaps up to a size of 3mm (1/8 inch). If you have a larger gap to fill up, you can load it with spins of soaked newspaper or soft rope. Bear in mind to always fill up the tub with water prior to securing, to permit the motion experienced when the bathtub remains in use. The sealant can split rather very early if you do not think about this movement before securing.
Additionally, ceramic coving or quadrant floor tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are likewise conveniently available on the market. It is advisable to fit the ceramic tiles using water-resistant or water-proof glue and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I recently found that blog post about A Step-by-Step Guide to Installing a Bathtub while perusing the internet. Appreciated our blog? Please share it. Help somebody else check it out. We value reading our article about Installing A Bathtub.
High-quality, fast plumbing repairs. Report this page